The Perfect Overlap For Plastic Curtain Strips: How Much?

The amount of overlap on plastic curtain strips depends on the size of the doorway and the amount of traffic passing through it. For example, a doorway that is 8 feet wide and uses 6-inch strips with a 66% overlap will need 24 strips to cover the area. The more overlap there is, the tighter the seal, but the more difficult it is to pass through. Smaller doorways with less overlap are more suitable for pedestrian traffic, while larger doorways with more overlap are better for machinery and trucks.

The more overlap, the tighter the seal

The more overlap in plastic curtain strips, the tighter the seal. However, this also makes it more difficult to push through. For example, a 66% overlap on an 8-foot-wide door using 6-inch strips requires 24 strips to seal and cover the area. A 100% overlap, which means two layers of strips all the way across the doorway, is not recommended for pedestrian traffic.

Overlap is also important when making curtains. Curtain makers use various figures for overlap, with some adding 10% and others adding 2cm per 50cm of pole for ease plus overlap. However, it is important not to overdo it. If too much overlap is added, the extra fabric won't spread evenly across the curtain, and a section of the curtain will stay stacked back at each side when pulled closed.

Overlap is also a consideration when choosing a strip width and configuration for industrial strip curtains. Smaller doorways and pedestrian-only traffic can use less overlap with a more economical material. For larger openings or motorized traffic, a heavier strip is recommended.

The more overlap, the harder to push through

The more overlap there is on plastic curtain strips, the harder it is to push through. This is because the more overlap there is, the tighter the seal. However, the more overlap there is, the more economical the material is, as it requires less strip material.

Overlap is important for creating a tight seal, but it is also important to consider the ease of access. For smaller doorways and pedestrian traffic, using less overlap with a more economical material is suitable. This makes it easier for people to walk through the doorway.

For larger openings or motorized traffic, a heavier strip with more overlap may be necessary. However, it is important to note that larger strips with 100% overlap are not recommended for pedestrian traffic, as they may be too difficult to push through.

When calculating the overlap for plastic curtain strips, it is important to consider the size of the opening and the type of traffic that will be passing through. By using a table or guide, you can determine the appropriate overlap percentage and number of strips needed to adequately cover the opening.

The overlap percentage depends on the size of the opening

The overlap percentage of plastic curtain strips depends on the size of the opening. For example, an 8' wide door using 6" strips with 66% overlap needs 24 strips to seal and cover the area. The more overlap, the tighter the seal, but the more difficult it is to push through. Smaller doorways and pedestrian-only traffic can use less overlap with a more economical material. For larger openings, such as those accommodating forklift traffic, trucks, and machinery, a heavy-duty strip with less overlap is recommended. This uses less material and is easier to pass through.

When calculating the overlap for curtains, curtain makers may add 10% or 2cm per 50cm of pole for ease and overlap. It is important not to add too much, as this can cause the curtain to stack back at each side when pulled closed. In general, adding 4cm to each curtain for the overlap (creating an 8cm overlap as each curtain passes the middle by 4cm in opposite directions) plus 5% of the pole covered by the curtain is a good rule of thumb.

The overlap percentage depends on the type of traffic

For smaller doorways and pedestrian-only traffic, using less overlap with a more economical material is suitable. For bigger openings or motorized traffic, consider a heavier strip. For large openings, forklift traffic, trucks and machinery, a heavy-duty strip is required. If lighter loads are typically carried, too heavy a strip may drag the product off the forklift.

For high-traffic pedestrian areas, an industry-standard strip width using less overlap is perfect. This configuration is also good for walk-in coolers and carrying loaded serving trays or boxes through with ease.

The overlap percentage depends on the type of material

The more overlap, the tighter the seal, but the more difficult it is to push through. For smaller doorways and pedestrian traffic only, less overlap with a more economical material is suitable. For larger openings or motorized traffic, consider a heavier strip. If you are using lighter loads, a heavier strip may drag the product off of a forklift.

When making curtains, curtain makers may add 10% for ease and overlap, or 2cm per 50cm of pole. It is important not to add too much, as the extra will not spread evenly across the curtain. Instead, a section of the curtain will stay stacked back at each side when you pull the curtains closed.

Frequently asked questions