Omar Khalid
The Magic Bullet NutriBullet is a personal blender with a range of user-friendly attachments. The plastic and rubber gear in the blender wears down quickly, making it simple to replace. To change the plastic driver, you must first remove the base plate with four screws. Then, wiggle the plastic fan off the screw head and grip the ribbed shaft with pliers while turning the plastic base gear. The plastic drive wheel can be removed by turning it clockwise, and it can be tightened by turning it anti-clockwise.
| Characteristics | Values |
|---|---|
| Appliance | Magic Bullet NutriBullet |
| Appliance type | Blender |
| Parts | Plastic base, blades, screw, nut, plastic fan, plastic gear, plastic drive wheel, plastic drive gear |
| Steps | Remove the base plate, grip the ribbed shaft with pliers, turn the plastic base gear, remove the bottom containing the blades, use oil to loosen rust, wiggle the plastic fan off the shaft, use a screwdriver and pliers to remove the base gear |
| Challenges | Soft metal, difficulty applying torque, rust, plastic breakage |
Explore related products
What You'll Learn
Removing the base plate
To remove the base plate of your Magic Bullet blender, you will need to first remove the bottom containing the blades from the rest of the appliance. There is a screw in the middle of the bottom of the appliance that needs to be unscrewed to lift the blade assembly portion out. This screw can be difficult to remove, so be patient and apply some force gently. If the gear is rusted, you may need to use some oil to loosen it up. Turn the plastic piece holding the blades so that the blade side is down and place a few drops of oil in the centre. Allow it to set for several minutes and then wipe off the excess oil with a paper towel.
Once the blade assembly is removed, you can access the base plate. The base plate is secured by four screws. Use a screwdriver to remove these screws, and then carefully lift the base plate away from the blender. It may be helpful to use a flat-head screwdriver to stop the post from rotating while you remove the nut.
If your Magic Bullet blender has a plastic fan, you may need to wiggle it off the shaft of the screw head. This is because the plastic fan can become stripped, making it difficult to get effective torque. In this case, you may need to use pliers to grip the ribbed shaft while turning the plastic base gear.
It is important to note that the threads on the Magic Bullet blender are opposite to those on standard blenders. The plastic drive wheel turns clockwise to remove or loosen, and anti-clockwise to tighten. Keep this in mind when reassembling the new drive disc.
Val Kilmer's Plastic Surgery: Did He or Didn't He?
You may want to see also
Explore related products
Removing the plastic fan
To remove the plastic fan from your Magic Bullet blender, you will need to first remove the bottom blade assembly. This can be done by unscrewing the screw in the middle of the bottom of the appliance. Be patient, as this screw can be difficult to remove.
Once the blade assembly is removed, you will see a plastic circle with a nut in the centre that holds the blades to the motor. This is the plastic fan you need to remove. You may need to use a flat-head screwdriver to stop the post from rotating while you take off the nut.
If the nut is difficult to remove, you may need to apply some oil to loosen it. First, turn the plastic fan so that the blades side is down. Then, place a couple of drops of 3-in-1 oil on the small metal section in the centre and allow it to set for several minutes. Wipe off the excess oil with a paper towel before attempting to remove the nut again.
Now, to remove the plastic fan, you will need to grip the ribbed shaft with pliers while turning the plastic base gear up top. Note that the threads on the Magic Bullet are opposite to most, so you will need to turn it clockwise to loosen it. Wiggle the plastic fan off the shaft of the screw head.
With these steps, you should be able to successfully remove the plastic fan from your Magic Bullet blender.
Plastic Fumes: Cyanide Poisoning Risk?
You may want to see also
Explore related products
Using a screwdriver and pliers
To change the plastic gear in a Magic Bullet blender, you will need to remove the cover. Start by unplugging your blender and putting on safety goggles to protect your eyes from the blades. Then, remove the three screws at the bottom of the cover using a flathead screwdriver. Once the screws are removed, you can pull off the cover.
The gears are located in the middle of the machine. Loosen the two screws holding the gears in place with a screwdriver, and if they are difficult to remove, use a pair of pliers to help. Once the screws are loose, you can pull out the gears and replace them with new ones. Make sure to tighten the screws before putting the cover back on.
If you are having trouble removing the blade, try using a pair of pliers to grip the ribbed shaft while turning the plastic base gear at the top. You can also use a flat-tip screwdriver on the bottom end while holding the pliers in place on the base gear. Turn the blade gear in a clockwise direction to remove it from the shaft.
When reassembling, pay attention to how the parts came apart so that you can put them back together correctly. Insert the new gear into place, and replace the rubber gasket, screw, and blade. Finally, plug in your blender and test it out!
Plastic Pollution: A Global Crisis and Challenge
You may want to see also
Explore related products
Replacing the plastic gear
To replace the plastic gear of your Magic Bullet blender, you will first need to remove the bottom containing the blades from the rest of the blender. There is a screw in the middle of the bottom of the appliance that unscrews so you can lift the blade assembly portion out. The screw holding the blade assembly can be challenging to remove, so be patient.
In some cases, the gear may be rusted, and you will need to use some oil to loosen it up before attempting to remove it. Turn the plastic piece holding the blades so that the blades side is down, and then place a couple of drops of 3-in-1 oil on the small metal section in the centre. Allow the oil to set for several minutes to loosen the rust, and then wipe it off with a paper towel.
Now, place a heavy-duty cloth in your hand and then the blade section of the blender, blade side down. You can then remove the base plate (4 screws), wiggle the plastic fan off the shaft of the screw head, and grip the ribbed shaft with pliers while turning the plastic base gear up top. Note that the Magic Bullet's threads are backward, so turn it clockwise to remove/loosen and anti-clockwise to tighten.
Replacement gears can be purchased at various online stores.
Building a Corrugated Plastic Roof: DIY Guide
You may want to see also
Explore related products
Cleaning and maintaining the blades
For a deeper clean, you can fill the cup with warm water and dish soap, screw on the extractor blade, and run the blender for 20 to 30 seconds. Alternatively, you can use a small brush for a deeper clean, but never submerge the power base in water and never put it in the dishwasher. If you prefer a dishwasher, it is recommended to rinse the blades and cups before placing them in the dishwasher, and to avoid using the sanitize cycle as it may warp the plastic.
If you encounter a spill within the power base, immediately shut down and unplug the blender. Remove the blade and cup and wipe up any spillage with a damp sponge or towel. Do not remove any parts from within the power base; simply clean around them.
It is important to note that the gasket, the rubber-band-looking thing inside the blade, should never be removed as it ensures a tight seal. If you wish to clean the gasket, hand washing with warm, soapy water is recommended over dishwashing as the heat may damage the gasket and cause it to loosen or fall out. To restore cloudiness, you can use a 10% solution of bleach or vinegar to water, filling the cup and allowing it to sit for a short time before rinsing, washing, and rinsing again.
To maintain the blades in optimal condition, it is recommended to replace them every six months if the blender is used regularly.
Plastic Product Identification: How Manufacturers Mark Their Goods
You may want to see also
Frequently asked questions
If your blender is leaking or if the plastic shell is cracked, you may need to change the bullet plastic driver.
First, remove the base plate (4 screws). Then, wiggle the plastic fan off the shaft of the screw head and grip the ribbed shaft with pliers while turning the plastic base gear up top.
The screw holding the blade assembly can sometimes be difficult to remove. Be patient and apply some oil to loosen it up.
Replacement gears can be purchased at various online stores.
