Omar Khalid
There are various ways to finish a plastic box lanyard, depending on the material used. If you're using thread-based material, such as craft lace, cut the ends close to the lanyard and burn them with a match or secure them with crazy glue. If you're using gimp or boondoggle material, you'll need to do a finishing stitch. Loosen the loops of your last stitch, then take one of your strands and pull it through the loop of the other strand of the same colour, going under the same-colour strand and the different-coloured strand beneath it. Repeat this for all four strands, pulling each strand tight and trimming them to your desired length. Another way to finish a lanyard is by tying a granny knot with the two uppermost strands, which are the two strands higher up the braid.
| Characteristics | Values |
|---|---|
| Material | Gimp, boondoggle, thread-based (e.g. craft lace) |
| Finishing stitch required? | Yes, if using gimp or boondoggle |
| Final step | Trim strands to desired length |
| Alternative ending | Tie a granny knot with the two uppermost strands |
| Alternative ending for thread-based lanyards | Burn ends with a match or secure with crazy glue |
Explore related products
What You'll Learn
Tie a granny knot with the two uppermost strands
To finish a plastic box lanyard, one of the final steps involves tying a knot with the two uppermost strands. This is called a granny knot, which is a type of single Carrick bend. It consists of two half knots, one tied above the other.
To tie a granny knot, start by crossing the two strands. Then, take the top strand and wrap it around the back strand. You have now created the first half of the knot. Repeat this step with the ends of the half knot you've just made. In other words, cross the ends, and then wrap the end of the top strand around the end of the back strand. Pull the knot tight, and you've successfully created a granny knot!
It is important to note that the granny knot is not considered a secure knot for critical applications. However, it can still be useful for various purposes, such as tying ribbons, shoelaces, or craft projects.
Enhancing Your Truck's Look: Darkening Plastic Trims
You may want to see also
Explore related products
Cut the ends close to the lanyard and burn them
To finish a plastic box lanyard, you can cut the ends close to the lanyard and burn them. This method is suitable for thread-based materials such as craft lace. Here is a step-by-step guide:
- Cut the ends of the lanyard: Use a sharp pair of scissors to trim the excess cord or strands close to the lanyard. You can cut the strands as short as possible, almost flush with the lanyard, but be careful not to cut the actual lanyard. This step ensures that you have a neat and tidy finish, with minimal excess material to deal with.
- Prepare your burning tool: You will need a lighter or a match to melt the ends of the lanyard. A small, handheld lighter, such as a Bic lighter, is recommended for ease of handling. Alternatively, you could use a match if you prefer.
- Apply heat to the ends: Hold the flame of the lighter or match near the end of the lanyard, close enough for the heat to melt the material. Be careful not to hold the flame directly onto the lanyard, as this may cause it to catch fire. You should aim to melt the end of the lanyard, not burn it.
- Melt the ends: Keep the lanyard end close to the bottom of the lighter flame, where it is not as hot. Hold it there for about 2 seconds, or until you see the material start to melt and turn shiny. This will seal the frayed ends of the cut lanyard, giving it a smooth and finished appearance.
- Cool down: Once the ends are melted and sealed, remove the flame from the lanyard. Allow the lanyard to cool down for a short period, about a minute, before handling it. This will ensure that the melted ends are set and also prevent any accidental burns.
- Inspect and adjust: After cooling, inspect your lanyard. If there are any minor imperfections or charred areas, you can use a permanent marker in a matching colour to touch up and hide any imperfections. This step is optional but can help create a more uniform and polished final product.
By following these steps, you can effectively finish your plastic box lanyard by cutting the ends close to the lanyard and using a heat source to melt and seal the frayed edges. This technique is a simple and quick way to give your lanyard a neat and durable finish.
Deep Scratches on Plastic Lenses: Repair or Replace?
You may want to see also
Explore related products
Secure with crazy glue
When finishing a plastic box lanyard, the method you use will depend on the material you are working with. If you are using a thread-based material, such as craft lace, you can secure the lanyard with crazy glue. Here is a step-by-step guide on how to do this:
First, cut the ends of your thread close to the lanyard. Ensure that you leave enough thread to work with when applying the glue. Be careful not to cut the lanyard itself.
Next, apply a small amount of crazy glue to the cut ends of the thread. You only need a tiny amount of glue, as a little goes a long way. Be cautious, as super glue can bond skin and eyes together very quickly. It is recommended to wear gloves and eye protection when working with super glue.
Now, carefully press the glued ends of the thread against the lanyard. Hold them in place for a few seconds to ensure the glue sets properly. You may want to use a tool, such as a toothpick, to apply pressure and avoid getting glue on your fingers.
Finally, allow the glue to dry completely. Crazy glue typically sets very quickly, but it is best to let it dry for a few minutes to ensure a strong bond. Once the glue is dry, your plastic box lanyard will be securely finished and ready to use.
By following these steps, you can securely finish your plastic box lanyard using crazy glue, resulting in a durable and professional-looking product.
The Easy Guide to Installing Plastic Lattice
You may want to see also
Explore related products
Loosen the loops of the last stitch
The square stitch is one of the most basic stitches to use for lanyards. To finish a square stitch, stitch one more square stitch but do not pull it tight. Keep it loose. Then, pull one strand to the left of the square stitch and bring it up and through the opposite loop, up through the loose middle stitch. Repeat this process with the strand on the left of the first strand, pulling it around the square stitch to the left and bringing it up through the opposite loop and the middle stitch.
If you are using a thread-based material, such as craft lace, you can simply cut the ends close to the lanyard and burn them with a match or secure them with glue. However, if you are using gimp or boondoggle material, you will need to do a finishing stitch as mentioned above.
After completing the finishing stitch, pull all four strands until your knot is tight. Pull on your strands that are hanging out gently until they are pulled taut and cannot be moved around easily. Make sure your knot is tight enough that the strands won't fall apart, but not so tight that it warps or puckers your lanyard. Finally, cut the excess strands to your desired length.
Plastic Pollution: Fish Immune Systems Under Attack
You may want to see also
Explore related products
Pull each strand through the centre of the lanyard
When finishing a plastic box lanyard, it's important to know how to end it securely. One of the most basic stitches to use when ending a lanyard is the square stitch. This stitch can be used as a foundation for creating larger and different lanyards.
To end a square stitch, you will need to stitch one more square stitch but don't pull it tight—keep it loose. Then, pull one strand and bring it around the side of the square stitch to the left. Pull it up and through the opposite loop, and then through the middle stitch. Repeat this process with the strand to the left of the first strand. Pull it around the square stitch to the left and bring it up through the opposite loop, and then through the middle stitch.
If you're using gimp or boondoggle material, you'll need to do a finishing "stitch." First, loosen the loops of your last stitch. Then, take one of your strands and pull it through the loop of the other strand of the same colour, going under the same-colour strand and the different-coloured strand beneath it. Finally, pull your strand up through the centre of the lanyard. Repeat this process for all four strands, pulling each strand tight when they're all through.
Finally, trim the strands to your desired length. You can simply cut the ends close to the lanyard and burn them with a match or secure them with crazy glue.
Septic Tank Laws in Georgia: Are Plastic Tanks Legal?
You may want to see also
Frequently asked questions
Pull the strands with one hand through the middle stitch and in the opposite direction of the lanyard. Pull them tight to secure the lanyard, but not so tight that it might break. Cut the remaining strands to the desired length.
Cut the ends close to the lanyard and burn them with a match or secure them with crazy glue.
Tie a granny knot using the two uppermost strands. A granny knot consists of two half knots: cross the strands, wrap your top strand around your back strand, and then repeat this for the ends of the half knot you've just created.
Loosen the loops of your last stitch a bit first. Then, take one of your strands and pull it through the loop of the other strand of the same colour, going under the same-colour strand and the different-coloured strand beneath it. Pull your strand up through the centre of the lanyard. Repeat this for all four strands, pulling each strand tight and then trim them to your desired length.
![Clear ID Badge Holder with Lanyard, Weather Resistant PVC Plastic Resealable Zip Cruise Ship ID Vertical Card Holder with Detachable Quick Side Release Snap Buckle [Pack of 2]](https://m.media-amazon.com/images/I/615LBpMiAgL._AC_UL320_.jpg)
