Sofia Martinez
Painting a Savage plastic stock requires careful preparation to ensure the paint adheres correctly. It is recommended to use a degreaser, such as acetone, to clean the stock and remove any oils or residue. The surface should then be roughed up with a Scotch pad or sandpaper to create a texture that will help the paint stick. After cleaning and roughing, a primer should be applied, followed by the chosen paint colour. It is important to allow adequate drying time between coats and a clear matte sealing coat can be applied for extra protection and a durable finish. Some recommended products include Krylon spray paints, Duracoat, Bulldog, and Cera Kote.
Explore related products
$11.99
What You'll Learn
Degreasing and cleaning the stock
First, you'll want to remove any existing paint, dirt, or oils from the surface of the stock. This can be done by using a product like acetone, which will help strip away any old paint and prepare the surface for the new coat. Ensure you wipe down the stock thoroughly with a rag soaked in acetone, as suggested by some gun enthusiasts. This process is crucial as it will soften the plastic surface, making it more receptive to the new paint and promoting better adhesion.
Next, you'll want to give the stock a thorough cleaning. Fill a bucket with warm water and add a mild detergent or dish soap. Use a sponge or a rag to scrub the stock, ensuring you reach all the crevices. This step will remove any remaining dirt, grease, or debris. If your stock has mildew or heavy soiling, you may need to use a scrub brush and repeat the washing process to ensure it is thoroughly cleaned. Remember to wear protective gloves and work in a well-ventilated area when handling acetone or other strong cleaning agents.
Once the stock is clean and dry, it's essential to prepare the plastic surface to ensure the paint adheres well. Start by sanding the stock with a fine-grit sandpaper, such as 220-grit. This process will create a rougher surface for the paint to grip onto. Sand the stock evenly, aiming for a matte finish rather than a glossy one. You can use a Scotch-Brite pad for this step if preferred. Remember to wear a dust mask to avoid inhaling plastic dust.
After sanding, wipe down the stock with a clean rag dampened with mineral spirits or isopropyl alcohol. This step will remove the fine plastic dust generated during the sanding process and ensure the surface is ready for priming and painting. It is crucial to work in a well-ventilated area when using mineral spirits, and always follow the manufacturer's safety instructions.
Finally, if you want to go the extra mile, consider using an adhesion promoter or a specialised plastic primer. These products will further enhance the adhesion of the paint to the plastic surface. Choose a primer that is suitable for use with spray paint and apply it according to the manufacturer's instructions. Allow the primer to dry completely before moving on to the painting stage. Remember, taking your time and following these steps will ensure a clean and well-prepared surface for your Savage plastic stock, resulting in a smoother painting process and a more durable finish.
Restoring Chrome-Painted Plastic: Tips for a Perfect Finish
You may want to see also
Explore related products
Sanding and roughing up the stock
Before painting a plastic stock, it is important to sand and roughen the surface to ensure the paint will adhere properly. This process involves several steps:
Firstly, it is essential to start with a clean surface. Use a degreaser or cleaner to wipe down the stock and remove any oils, dirt, or other contaminants. Common products used for this purpose include acetone, lacquer thinner, alcohol, or auto body cleaner/degreaser. This step is crucial because any remaining grease or oil can prevent the paint from adhering properly to the surface.
Next, you'll want to rough up the surface of the stock. This can be done in several ways, depending on the tools you have available. Some people use sandpaper, such as 1500-grit emory paper, to lightly sand the surface and create a rough texture. Others use a Scotch-Brite or Scotch pad to scrub the stock and remove the sheen, creating a slightly textured surface for the paint to grip. This step is crucial because it provides a "tooth" for the paint to bite into, improving adhesion.
After the surface has been roughed up, it is essential to wipe it down again with a thinner or solvent, such as acetone or mineral spirits. This step will remove any remaining dust or debris from the sanding process and ensure a clean surface for painting.
It is worth noting that some people choose to use a primer after the sanding and roughing process. A primer can further improve paint adhesion and provide a better surface for the paint to adhere to. However, it is crucial to follow the manufacturer's instructions and allow the primer to dry completely before proceeding.
Finally, once the surface is prepared, you can begin the painting process. It is important to follow the manufacturer's instructions for the specific paint you are using, including any recommended drying or curing times.
Remember, when painting a plastic stock, the key to success is proper surface preparation. Taking the time to sand and rough up the stock will ensure that your paint job adheres properly and lasts for years to come.
Painting Plastic Bumper Bars: A Step-by-Step Guide
You may want to see also
Explore related products
$19.99 $22.79
Applying primer
To apply primer to a plastic surface, you must first clean the surface with warm water and detergent to remove any dirt or oils. Once the surface is clean and dry, you can begin to roughen the plastic. This can be done with a Scotch pad, sandpaper, or a product like Scotchbrite. The goal is to remove the sheen from the plastic and create a surface to which the primer can adhere. After this, wipe the surface with an alcohol solution and let it dry.
Next, you will want to apply an adhesion promoter to the prepared plastic. This will help the primer and paint fuse to the plastic. You can then apply a light tack coat of primer to the surface. It is important to note that while the primer may feel dry to the touch in 15 minutes, it can take a day or two to fully cure. Be sure to follow the manufacturer's instructions for the primer you are using.
Once the primer is fully cured, you can apply a second light coat of primer. After this coat has been applied, you will again need to let the primer cure for a day or two. This will ensure that the primer is fully cured before you begin painting. It is important to be patient and apply light coats of primer and paint to avoid any issues with the finish.
Additionally, if you are working with a repaired plastic surface, there are a few extra steps you should take. Before applying primer, you should triple-clean and sand the repaired area, feathering the repair edge as needed. You should also apply an adhesion promoter to the newly repaired area, extending it slightly beyond the feathered edge to ensure full coverage.
Curing Enamel Paint on Plastic: The Ultimate Guide
You may want to see also
Explore related products
$13.85 $16.29
Painting the stock
Before painting a plastic stock, it is important to prepare the surface to ensure the paint will adhere properly. Start by degreasing and de-oiling the stock with a product like acetone, lacquer thinner, or alcohol. This will remove any oils or residue and prepare the surface for painting. You can also use a Scotch-Brite or Scotch pad to scuff up the surface and create a rough texture for the paint to adhere to. Be sure to wipe down the stock with a clean rag after scuffing to remove any dust or debris.
Once the surface is prepared, it's time to apply a primer. A primer will help the paint adhere better and create a more even finish. Choose a primer specifically designed for plastic surfaces, such as Bulldog or Krylon Fusion. Apply a light tack coat of primer to the stock, followed by another light coat. Allow the primer to dry completely according to the manufacturer's instructions before moving on to the next step.
Now it's time to apply the paint. Choose a paint that is suitable for plastic surfaces and your desired colour. Krylon offers a wide range of colours, including camouflage patterns and flat finishes. You can use spray paint or traditional paint with a brush, depending on your preference and the paint you have chosen. If using spray paint, be sure to follow the manufacturer's instructions for proper application and safety. Apply light coats of paint, allowing sufficient drying time between each coat.
After the paint has dried, you may want to consider applying a clear coat or topcoat for added protection and durability. A clear matte finish can provide a sleek and subtle look, while also protecting the paint underneath. Again, allow the clear coat to dry completely before handling the stock.
Finally, once the paint and clear coat are fully cured, you can lightly sand or rub the surface with fine-grit sandpaper or steel wool to create a smooth finish. This step is optional but can help create a more professional and polished look.
Painting Plastic Cases: Translucent Transformation Techniques
You may want to see also
Explore related products
Sealing the paint
Before sealing, it is important to sand down the surface with fine-grit sandpaper (120 to 220 grit) to create a rough texture that will help the sealant and paint adhere better. You can then use a blower, vacuum, or cloth to remove the dust. If you are using multiple colours, you can use masking tape to create a border and prevent the colours from bleeding into each other.
For small items, spray sealants work well, whereas larger surfaces are better suited to brush-on sealants. It is important to let each layer of sealant dry completely before applying the next.
Some specific products that can be used to seal paint on plastic include:
- Mod Podge Acrylic Sealer Spray
- Acrylic-based lacquer
- Bulldog IIRC (a primer designed for plastic)
Painting Plastic: Revamping Your Four-Wheeler's Look
You may want to see also
Frequently asked questions
First, you need to degrease/de-oil the stock with a product like acetone or lacquer thinner. Then, lightly sand the stock with sandpaper and wipe it down with acetone again. Tape up any areas that you don't want to be painted. Once dry, apply a light coat of primer. After the primer dries, apply your choice of paint.
You can use Krylon spray paints as they work well on plastic stocks. You can also use Bulldog IIRC, a special primer for plastic parts.
Cera Kote is the best paint for a gun stock as it resists UV damage well.
You can either paint the inside of the stock lightly or mask it with painter's tape.
Paint on a gun stock typically takes 48 hours to dry. However, it is recommended to let it cure for two weeks before using the gun.
