The Cost Of Plastic Spools: Understanding The Price Breakdown

A spool of plastic is used for 3D printing. The average 1kg spool of filament costs between $30 and $50 and lasts just over a month. A spool of this size can yield around 700-800g of printed output, which is enough to print about 20-30 mid-sized models.

3D printing plastic costs $30 to $50 per kilogram

The cost of 3D printing plastic ranges from $30 to $50 per kilogram. The average 1kg spool of filament lasts just over a month before it needs replacing. A 1kg spool of 1.75mm PLA filament contains approximately 560-570 metres of filament, which is enough to print about 20-30 mid-sized models. A 1kg spool of good quality PLA filament will yield around 700-800g of printed output. This is equivalent to printing roughly 20-30 mid-sized models at 6 inches tall with default slicer settings.

A 1kg spool of 1.75mm PLA filament contains 560-570 metres of filament

PLA filament is a type of 3D printing plastic that costs on average $30 to $50 per kilogram. It is possible to recycle scrap plastic by re-extruding it into usable filament. On average, a 1kg spool of good quality PLA filament will yield around 700-800g of printed output.

To maximise the lifespan of a 1kg spool of filament, there are several best practices to follow. These include tweaking print settings for efficiency, such as enabling settings like "sparse infill" and "infill before walls" to reduce wasted material inside prints. It is also recommended to use higher infill only where needed, limiting top/bottom infill to the minimum required for structural integrity to save plastic.

A 1kg spool of good quality PLA filament yields 700-800g of printed output

A 1kg spool of good-quality PLA filament will yield 700-800g of printed output. This is enough to print about 20-30 mid-sized models, depending on the infill percentage. A lower infill will allow you to print more items from a spool, but the strength of the models will be reduced.

The average 1kg spool of filament lasts users just over a month before it needs replacing. The 3D printing plastic cost for an ASA spool is around $30 to $50 per kilogram.

A 1kg spool of filament lasts just over a month

The average 1kg spool of filament lasts users just over a month before it needs replacing. The cost of a spool of plastic ranges from $30 to $50 per kilogram. The length of time a 1kg spool of filament lasts depends on how often you use your 3D printer. For example, if you 3D print on a daily basis and create larger models, you could use 1kg of filament in a week or so. On the other hand, if you only use your 3D printer once a week for five hours, a spool will last you a little over six months.

A 1kg spool of 1.75mm PLA filament contains approximately 560-570 metres of filament. This is enough to print about 20-30 mid-sized models. On average, a 1kg spool of good quality PLA filament will yield around 700-800g of printed output. This is equivalent to printing roughly 20-30 mid-sized models at 6 inches tall with default slicer settings.

To maximise the lifespan of a 1kg spool of filament, there are several best practices you can follow. For example, tweaking print settings for efficiency by enabling settings like "sparse infill" and "infill before walls" can reduce wasted material inside prints. Additionally, using higher infill only where needed can save plastic while maintaining structural integrity.

1kg of ABS is about a litre, 1kg of PLA is about 0.8 litres

The cost of a spool of plastic depends on the type of plastic. For example, a spool of ASA plastic costs around $30 to $50 per kilogram. A spool of ABS plastic is about one litre per kilogram, while a spool of PLA plastic is about 0.8 litres per kilogram.

A 1kg spool of 1.75mm PLA filament contains approximately 560-570 metres of filament. This is enough to print about 20-30 mid-sized models. A 1kg spool of good-quality PLA filament will yield around 700-800g of printed output. To maximise the lifespan of a 1kg spool of filament, you can tweak print settings for efficiency. For example, enabling settings like "sparse infill" and "infill before walls" can reduce wasted material inside prints. Using higher infill only where it is needed will also save plastic.

Frequently asked questions